Pedego Tech Tips: How to Operate The Display of Your Pedego Electric Bike
Overview of the Pedego Display
When you turn on the Pedego display (which can be done by single pressing the power button), you come across your first screen. This is your main display. At the top of the screen, there is your speedometer. Immediately underneath is the battery charge. Underneath that, there is a trip meter, riding time, and odometer (they can be switched by single pressing the "set" button). To the left of the screen is the pedal assist level (which will always start at 0 and can be increased or decreased by pressing the plus and minus buttons).
How to Clear the Trip Meter on Your Pedego
Turn on your Pedego display by single pressing the power button. Press and hold the set button (underneath the power button) until it becomes backlit. There are different settings.
Set (1) will be your Trip Meter. To clear the trip odometer, single press the minus key. Press and hold the set button to go back to the main menu.
Powering on the Lights of Your Pedego Electric Bike
If your bike display is not on, single press the power button. Once you are on the main riding screen, single press the power button again. The screen will light up, and this will activate both your head and tailight.
To turn off the lights, single press the power button; the backlight on the display will turn off as well as the head and tailight.
How to Set Throttle Top Speed on Your Pedego Electric Bike
When you have your bike powered on, press and hold the "set" button until it becomes backlit. Single press the "set" button to reach the second menu. You can single press the plus button to increase and the minus button to decrease your speed. This will only affect the top speed of your throttle. Press and hold the "set" button to save your new setting.
What to do if you see an Error Code on your Pedego Display
Single press your power button to turn on the display. If there is a flashing error message next to the battery indicator, then you should call the Pedego Tech Support at 800-646-8604 or your local Pedego dealer. If you purchased your bike through Electric Bike Place or MACkite, please call 800-622-4655.
How to Engage the Pedal Assist Limiter on your Pedego
Power on your bike. Next, press and hold the "set" button until it becomes backlit. Press the "set" button until you reach Set 5. When set to "on", you will have an unregulated bike. You can single press the plus or minus and set the PAS to "off". When it is set to "off", you will have a reduced top speed through all pedal assist modes. Press and hold the set key until you revert back to the main menu.
How to Power on the USB Port on your Pedego
Turn on your display. To activate the USB port, press the "set" and plus button for 3 seconds until you see the USB icon. You can then remove the rubber cover and insert your USB cable into the bottom of your display.
How to Engage the Throttle Limiter on your Pedego
Turn on your display. Press the "set" button until the screen is backlit. Press "set" until you reach level 6. When your indicator is set to "on", then your throttle will be unregulated. Press the plus or minus button to regulate your throttle output to walking speed. Hold the "set" button to save your changes.
Understanding Battery Communication Functions on the Pedego Ridge Rider & Trail Tracker
Turn on the display. On your screen, you will notice a "BMS". Select Pedego models have battery communication. You can see your type of battery communication above the battery indicator.
The following symbols above the battery indicator show the following battery communication types. You may change the battery communication type by pressing the "set" and plus button together.
- % - Percentage output from the battery (for example, 35% output)
- O - Battery cycles (for example, 6 cycles to the battery)
- V - Battery voltage (for example, 47.1-volts)
How to Change the Wheel Size Setting of your Pedego
Turn on the display. Press and hold the "set" button until it becomes backlit. Single press the "set" button two times. "Set 3" will be the wheel size. You can press the plus or minus button to increase or decrease your wheel size. To save, press and hold the "set" key.
How to Change between MPH & KPH on your Pedego
Turn on the display. Press the "set" button until it becomes backlit. Next, single press the "set" button three times until you reach "Set 4". To change between MPH and KPH, single press the plus or minus key. Once you have chosen your preference, hold the "set" button to save your changes.